Automation guides
Control circuits, comms cable and panel loading for an automation installation.
- 5 min readWorked examples index by tool and tradeEvery AmpSize worked example in one place, grouped by calculator and tagged with the trade it was written for, from house circuits to industrial boards.

- 3 min readIDMT grading main switch and submainTwo IEC standard inverse relays graded at an 8 kA fault on a commercial building, showing how an instantaneous setting overrides the curve and sets the margin.

- 3 min readIEEE 1584-2002: arc flash model and limitsWhat the IEEE 1584-2002 empirical model governs, where it stops applying, and a 400 V switchboard study that lands on 7.54 cal/cm² at 455 mm.

- 3 min readDairy shed IDMT relay setting and gradingThree IDMT relays at a 3000 A fault, two grading margins and one curve inversion between the shed main and the farm incomer, read off the AmpSize relay engine.

- 3 min readIEC 60255-151: IDMT curve constantsWhat IEC 60255-151 governs, which curve sets the IDMT tool carries, and a worked grading pair on standard inverse that clears in 0.21 s and 0.74 s.

- 3 min readBattery backup for a PLC panel at 24 V DCSizing a 24 V DC backup bank for an 80 W PLC panel over one day of autonomy, with the daily energy, the daily charge and the bank capacity the tool returns.

- 3 min readArc flash boundary at a motor control centreArcing current, incident energy and arc flash boundary for a 400 V MCC at 25 kA with a 0.1 s clearing time, and why the equipment type moves the result.

- 3 min readMotor starting current for a 55 kW DOL startFull load current, DOL starting current, shaft speed and torque for a 55 kW four pole motor at 400 V, and what a soft starter or a VSD changes.

- 4 min readSwitchboard fault rating at 25 kA for 1 sA 1 second withstand check at 25 kA on 185 mm² copper XLPE, returning a 174.83 mm² minimum size and a 26.46 kA withstand, with a thin margin explained.

- 3 min readTransformer secondary fault current for 500 kVAA 500 kVA 11 kV to 400 V transformer at 6 percent impedance, worked through to 721.69 A of secondary full load current and 12,028.13 A of fault current.

- 3 min read24 V DC voltage drop on an instrument loopA 4-20 mA loop runs 200 m on 2.5 mm² at 24 V. See the mV/A·m figure, the 7.51 percent drop and the maximum length the engine returns for a 10 percent limit.

- 3 min readArc flash incident energy at a 400 V switchboardA 400 V board with 20 kA bolted fault and 0.2 s clearing gives 6.23 cal/cm² at 455 mm, an arcing current of 9.64 kA and a 1395.97 mm boundary.

- 4 min readAS/NZS 3008.1.2 Table 52: the k factorWhat Table 52 governs, how the adiabatic check uses k, and a 10 kA fault cleared in 0.1 s that needs 22.11 mm² against an installed 25 mm² conductor.

- 3 min readIDMT curve grading for a 100 A feederTwo standard inverse relays at 2000 A give a feeder trip at 0.23 s, an incomer trip at 0.99 s and a grading margin of 0.76 s, read off one chart.

- 5 min readDC cable size: 48 V battery and 600 V PV arrayTwo d.c. circuits sized to AS/NZS 3008.1.1:2025, a 48 V battery-to-inverter run that current sizes and a 600 V array feed that voltage drop sizes.

- 3 min readMotor full load current: 11 kW 400 V DOLFull load current, shaft speed, torque and direct on line starting current for an 11 kW four-pole 400 V induction motor, with the figures the tool returns.

- 3 min readProspective fault current at a main switchboardA 16 kA fault cleared in 0.1 s on 70 mm² copper XLPE, with the minimum conductor size, the withstand current and the k factor the adiabatic check returns.

Calculators these guides use
- Cable size calculatorFind the smallest cable size that passes each check.
- IDMT grading calculatorPlot the trip curves of inverse-time overcurrent relays.
- Arc flash calculatorEstimate the energy of an arc flash and its PPE category.
- Battery bank calculatorCalculate battery bank capacity and autonomy for a load.
- Motor calculatorFind motor full load current, starting current and torque.
- Cable fault rating calculatorCheck that a conductor can withstand the fault current.
- Transformer calculatorCalculate transformer full load current and impedance.
- Voltage drop calculatorCalculate voltage drop on a cable run and check the limit.
- DC cable size calculatorSize a d.c. cable up to 1500 V for current and voltage drop.