Automation أدلة
دوائر التحكم وكابل الاتصالات وتحميل اللوحة لتركيب أتمتة.
- قراءة 3 دقيقةIEEE 1584-2002: arc flash model and limitsWhat the IEEE 1584-2002 empirical model governs, where it stops applying, and a 400 V switchboard study that lands on 7.54 cal/cm² at 455 mm.
- قراءة 3 دقيقةDairy shed IDMT relay setting and gradingThree IDMT relays at a 3000 A fault, two grading margins and one curve inversion between the shed main and the farm incomer, read off the AmpSize relay engine.
- قراءة 3 دقيقةIEC 60255-151: IDMT curve constantsWhat IEC 60255-151 governs, which curve sets the IDMT tool carries, and a worked grading pair on standard inverse that clears in 0.21 s and 0.74 s.
- قراءة 3 دقيقةBattery backup for a PLC panel at 24 V DCSizing a 24 V DC backup bank for an 80 W PLC panel over one day of autonomy, with the daily energy, the daily charge and the bank capacity the tool returns.
- قراءة 3 دقيقةArc flash boundary at a motor control centreArcing current, incident energy and arc flash boundary for a 400 V MCC at 25 kA with a 0.1 s clearing time, and why the equipment type moves the result.
- قراءة 3 دقيقةMotor starting current for a 55 kW DOL startFull load current, DOL starting current, shaft speed and torque for a 55 kW four pole motor at 400 V, and what a soft starter or a VSD changes.
- قراءة 4 دقيقةSwitchboard fault rating at 25 kA for 1 sA 1 second withstand check at 25 kA on 185 mm² copper XLPE, returning a 174.83 mm² minimum size and a 26.46 kA withstand, with a thin margin explained.
- قراءة 3 دقيقةTransformer secondary fault current for 500 kVAA 500 kVA 11 kV to 400 V transformer at 6 percent impedance, worked through to 721.69 A of secondary full load current and 12,028.13 A of fault current.
- قراءة 3 دقيقة24 V DC voltage drop on an instrument loopA 4-20 mA loop runs 200 m on 2.5 mm² at 24 V. See the mV/A·m figure, the 7.51 percent drop and the maximum length the engine returns for a 10 percent limit.
- قراءة 3 دقيقةArc flash incident energy at a 400 V switchboardA 400 V board with 20 kA bolted fault and 0.2 s clearing gives 6.23 cal/cm² at 455 mm, an arcing current of 9.64 kA and a 1395.97 mm boundary.
- قراءة 4 دقيقةAS/NZS 3008.1.2 Table 52: the k factorWhat Table 52 governs, how the adiabatic check uses k, and a 10 kA fault cleared in 0.1 s that needs 22.11 mm² against an installed 25 mm² conductor.
- قراءة 3 دقيقةIDMT curve grading for a 100 A feederTwo standard inverse relays at 2000 A give a feeder trip at 0.23 s, an incomer trip at 0.99 s and a grading margin of 0.76 s, read off one chart.
- قراءة 5 دقيقةDC cable size: 48 V battery and 600 V PV arrayTwo d.c. circuits sized to AS/NZS 3008.1.1:2025, a 48 V battery-to-inverter run that current sizes and a 600 V array feed that voltage drop sizes.
- قراءة 3 دقيقةMotor full load current: 11 kW 400 V DOLFull load current, shaft speed, torque and direct on line starting current for an 11 kW four-pole 400 V induction motor, with the figures the tool returns.
- قراءة 3 دقيقةProspective fault current at a main switchboardA 16 kA fault cleared in 0.1 s on 70 mm² copper XLPE, with the minimum conductor size, the withstand current and the k factor the adiabatic check returns.
الحاسبات التي تستخدمها هذه الأدلة
- حاسبة وميض القوس الكهربائيقدّر طاقة وميض القوس الكهربائي وفئة PPE.
- حاسبة تدرّج IDMTارسم منحنيات فصل مرحّلات التيار الزائد ذات الزمن العكسي.
- حاسبة مجموعة البطارياتاحسب سعة مجموعة البطاريات والاستقلالية لحمل معين.
- حاسبة المحركحدّد تيار الحمل الكامل للمحرك وتيار البدء وعزم الدوران.
- حاسبة تحمّل الكابل لتيار العطلتحقّق من أن الموصل يتحمل تيار العطل.
- حاسبة المحوّلاحسب تيار الحمل الكامل والمعاوقة للمحوّل.
- حاسبة هبوط الجهداحسب هبوط الجهد على مسار الكابل وتحقّق من الحد.
- حاسبة مقاس كابل DCحدّد مقاس كابل d.c. حتى 1500 V للتيار وهبوط الجهد.