Whakawhiti ki te ihirangi
AmpSize

This page is not in Te reo Māori yet, so you are reading the English.

· 3 meneti te pānui

IDMT grading main switch and submain

Tātaitai IDMT grading

+2 references
IEC 60255-151 Annex AAS/NZS 3000:2018 Cl 2.5.7.2

Worked to AS/NZS 3000:2018. Tables checked 26 Sept 2026.

A large moulded case circuit breaker with an electronic trip unit in a main switchboard.

A fault on a tenancy submain should trip the submain relay and leave the main switch closed. This page grades two relays in a commercial building at an 8 kA fault and reads the margin.

The inputs

The fault current is 8000 A at the submain.

Submain relay:

  • Curve: IEC standard inverse
  • Pickup: 160 A
  • Time multiplier: 0.15
  • Instantaneous pickup: 2000 A

Main relay:

  • Curve: IEC standard inverse
  • Pickup: 400 A
  • Time multiplier: 0.35
  • Instantaneous pickup: none

Relay order sets which pair the tool compares. The downstream device goes first.

The clause

IEC 60255-151 Cl 5.2 defines the inverse time characteristic. Annex A gives the constants for the standard inverse curve. The same constants drive both relays here, so only the pickup and the time multiplier separate them.

AS/NZS 3000:2018 Cl 2.5.7.2 covers discrimination between protective devices in an installation.

The steps

The tool reads each curve at 8000 A.

The submain relay never reaches its curve. 8000 A is above its instantaneous pickup of 2000 A, so the instantaneous element operates instead. The trip time drops to the relay minimum.

The main relay has no instantaneous setting, so it follows the standard inverse curve all the way. At 8000 A that curve gives a time in the region of eight tenths of a second.

  • Submain trip time: 0.01 s
  • Main trip time: 0.79 s
  • Margin, submain to main: 0.78 s

The result

The margin is 0.78 s. The default warning threshold in the tool is 0.3 s, and no warning appears here. The pair grades.

The instantaneous setting did the work. Without it, the submain relay would follow its own curve at 8000 A. The margin would then come from the time multiplier difference alone. That margin is smaller and it narrows as the fault current rises.

An instantaneous element brings a cost. It removes grading below the submain. Any device further downstream now competes with a 0.01 s trip. A fault on a final subcircuit can take the submain out with it. Set the instantaneous pickup above the highest fault current at the next board down. The load current is not the figure to grade against.

The 0.79 s main trip time also has to suit the equipment. Cable withstand and arc flash energy both scale with clearing time. Feed 0.79 s into the fault rating tool for the submain cable. Feed it into the arc flash tool for the board label. Do that before you accept the setting.

Pickup is the other half of the grading. The submain pickup of 160 A sits above the tenancy load. It also sits below the lowest fault current on that submain. The main pickup of 400 A does the same job one level up. A pickup set too high leaves a low current fault uncleared.

The standard inverse curve is flat at high currents. Both relays sit far out on the flat part at 8000 A. That is why the curve alone gives a thin margin. It is also why the instantaneous element earns its place on the submain.

Check the grading at more than one current. At 1500 A the submain sits below its instantaneous pickup and follows its curve. The tool gives 0.46 s for the submain and 1.83 s for the main. The margin is 1.37 s. The margin is widest at low current and narrowest at high current. Grade the pair at the highest fault current the submain can see.

This page is a design aid. Verify every value against the current edition of the standard.

See also: Dairy shed IDMT relay setting and grading, IDMT curve grading for a 100 A feeder and Arc flash basics.

Whakamātau ki ēnei whakauru

Au hapa
8,000 A
Ngā whakawhiti
[{"name":"Submain","curve":"IEC-SI","pickupA"…
Whakatuwhera te tātaitai me ēnei whakauru

Hei whai ake

Ngā whakaaro o muri i tēnei

Ētahi atu tauira mahi

He āwhina hoahoa a AmpSize. Arotakehia ngā otinga ki te paerewa o nāianei.

He whai hua tēnei?

He pātai, he uara rānei e kitea ana he hē? Whakapā mai.