测试结果检查器
对照 Section 8 限值，检查实测测试结果。
Reads Electricity (Safety) Regulations 2010, AS/NZS 3000:2018 and AS/NZS 3017:2022. Tables checked 26 Sept 2026.
尝试一个工程 6
每项工作都会预填示例数值。请替换为您自己的数值。
- Check the test results of a new circuitWhether the insulation, earth, Zs and RCD readings pass on a 16 A circuit.
- Check a low insulation readingWhether 0.5 MΩ passes on a final subcircuit.
- Check Zs on a 32 A circuitWhether 0.6 Ω passes on a 32 A C‑curve circuit.
- Check a slow RCDWhether a 30 mA RCD that trips in 45 ms passes.
- Check a five-second circuitThe Zs limit for a submain with a 5 s disconnection time.
- Check earth continuity on a lighting circuitWhether 0.9 Ω passes on 1.5 mm².
输入
使用默认输入值的示例计算。
- 保护装置
- B 型断路器
- 保护装置额定值
- 20 A
- 切断时间
- 0.4 s
- 相线
- 2.5 mm²
- 绝缘测试情形
- 500 V 下的普通回路
- 检查绝缘电阻
- 是
- 实测绝缘电阻
- 50 MΩ
- 检查接地连续性
- 是
- 末端分路接地导体的实测电阻
- 0.3 Ω
- 检查回路阻抗
- 是
- 实测 Zs
- 1.2 Ω
- 检查 RCD 跳闸时间
- 否
- 极性已确认
- 是
验证
通过
- 绝缘电阻
- 合格。测得 50 MΩ，最小值 1 MΩ
- Earth continuity, subcircuit earth conductor
- 合格。测得 0.3 Ω，最大值 0.9 Ω
- 接地故障回路阻抗
- 合格。测得 1.2 Ω，最大值 2.9 Ω
此结果仅供设计参考。请对照现行标准进行核验。
计算步骤
- 绝缘电阻限值1MΩ
AS/NZS 3000:2018 Cl 8.3.6
- 测试电压500V
AS/NZS 3000:2018 Cl 8.3.6
- 接地连续性限值，subcircuit earth conductor0.9Ω
AS/NZS 3000:2018 Table 8.2
- 最大接地故障回路阻抗2.9Ω
AS/NZS 3000:2018 Table 8.1
- 额定电流 80% 时的最大 Rphe1.8Ω
AS/NZS 3000:2018 Table 8.2
- 额定电流 80% 时的最大 Re0.9Ω
AS/NZS 3000:2018 Table 8.2
- 绝缘电阻限值，AS/NZS 3017:20221MΩ
AS/NZS 3017:2022 Cl 4.5.4
- 总接地及等电位连接限值，AS/NZS 3017:20220.5Ω
AS/NZS 3017:2022 Cl 4.4.4
- 极性及回路接线已确认
AS/NZS 3017:2022 Cl 4.6.4
- 检查已通过3 of 3
关于此计算器
How this is calculated
The tool compares your measured test values with the limits for the circuit. Tick the tests you did. The tool checks only those.
- Insulation resistance. The tool reads the minimum and the test voltage from AS/NZS 3000 Cl 8.3.6. It also reads the AS/NZS 3017:2022 figure from Cl 4.5.4.
- Earth continuity. It reads the limit for the earth conductor size from Table 8.2. It also reads the limit at 80 % of the rated current. AS/NZS 3017:2022 Cl 4.4.4 gives the main earth and bonding limit.
- Loop impedance. It reads the maximum Zs for the device and disconnection time from Table 8.1.
- RCD trip time. It compares your measured time with the limit for the rated residual current.
- Polarity. You confirm polarity and connections. The tool does not measure them. It points at AS/NZS 3017:2022 Cl 4.6.4.
- Verdict. The result passes only when every test you ticked passes.
Worked example
- Lighting circuit, 2.5 mm² on a 20 A B curve breaker. Insulation is 50 MΩ against a 1 MΩ minimum. Earth continuity is 0.3 Ω against a 0.9 Ω maximum. Zs is 1.2 Ω against a 2.9 Ω maximum. The verification passes.
Limits
The tool does not take your readings. It does not correct a loop reading for temperature. A pass here is not a certificate. A competent person signs the verification. Use the loop impedance calculator to predict Zs before the test.
See also: Testing to Section 8, Earth fault loop impedance and maximum Zs and Table 8.1 maximum Zs explained.
问题
结果仅供设计参考。请依据现行标准核对。
测试结果工具有什么作用？
工具将您在现场测得的数值与 AS/NZS 3000 Section 8 的验收限值进行比较。它检查绝缘电阻、接地连续性、回路阻抗和 RCD 动作时间。每项检查均报告合格或不合格。总体结论为合格、不合格或未验证。
最小绝缘电阻是多少？
Clause 8.3.6.3 规定，直流 500 V 时为 1 MΩ。带护套的加热元件为 0.01 MΩ，RCD 功能接地连接为 0.05 MΩ。若存在浪涌保护或电子设备，测试电压可降至 250 V。
它采用哪个回路阻抗限值？
工具依据 AS/NZS 3000:2018 Table 8.1，按保护装置类型、额定值和切断时间，列出表中的最大 Zs。工具还会报告 Table 8.2 中在额定电流 80% 时的最大 Rphe 和 Re，适用于无负荷测试。
为何工具显示“未验证”？
您所要求的测试无法进行。Table 8.1 中没有与该保护装置额定值对应的行，或未选择任何测试。对于未进行的检查，本工具不会报告通过。请更改额定值，或使用回路阻抗工具。
AS/NZS 3017:2022 适用于哪些情况？
AS/NZS 3017:2022 给出各项检验测试的方法。其绝缘和总接地限值与 Section 8 一致，因此本工具两者均予引用。其回路阻抗表格保留一位小数，因此本工具的 Zs 采用 Table 8.1。
计算示例
- A test sheet for a house boardA test sheet for a six-circuit New Zealand house board, with the tests in the AS/NZS 3017 order and the limit for each reading, then the Australian sheet.
- Reading the wiring in an older houseA 1970s New Zealand house with yellow actives, a green earth and a black neutral. What each colour can be, what may stay, and how to sleeve new terminations.
背景
- The order of verification testsWhy AS/NZS 3017 tests earth continuity before insulation and loop impedance before RCDs, which circuits take which test, and where each limit comes from.
- Testing to Section 8: what each test provesThe Section 8 test sequence, what each test shows, and how a calculated earth fault loop impedance compares with the value a tester reads on site.
本工具读取的条款和表格
- AS/NZS 3000:2018 Cl 8.3Verification testing
- AS/NZS 3000:2018 Cl 8.3.6Insulation resistance test
- AS/NZS 3017:2022 Cl 4.4.4Earth continuity results
- AS/NZS 3017:2022 Cl 4.5.4Insulation resistance results
- AS/NZS 3017:2022 Cl 4.6.4Polarity and circuit connection results
- AS/NZS 3000:2018 Table 8.1Maximum earth fault-loop impedance for the total circuit
- AS/NZS 3000:2018 Table 8.2Maximum resistance of final subcircuits at 80 % rated current
- Cl 8.3.5.2 and 8.3.6.3Insulation resistance and earth continuity verification limits
表格最后核对于 26 Sept 2026。
相关工具
这是否有用？
有问题，或数值看起来有误？联系我们。