Bỏ qua nội dung
AmpSize

This page is not in Tiếng Việt yet, so you are reading the English.

· Đọc 5 phút

Worked examples index by tool and trade

Công cụ tính tiết diện cáp

+4 references

Worked to AS/NZS 3000:2018 and AS/NZS 3008.1.2:2017 (NZ). Tables checked 27 Sept 2026.

The inside of an electrician's van, with cable reels, tool cases and test gear on shelves.

Every guide on this site is one calculation, run end to end, with the table behind each number. The index below groups them by calculator and tags each one with the trade it was written for.

The shape of a worked example

Take the shortest case on the site. A single‑phase circuit carries 20 A at 230 V over 15 m. The cable is multicore copper with PVC insulation, enclosed in air at 30 °C. One circuit shares the route. The device is a 20 A C curve and Ze is 0.35 Ω.

Selection follows AS/NZS 3000:2018 Cl 3.4, with ratings from AS/NZS 3008.1.2:2017 Tables 4-21. The total derating factor is 1, so the required tabulated current stays at 20 A. The answer is 2.5 mm². The derated capacity is 23 A and the drop is 2.13 %. Zs is 0.62 Ω on a 2.5 mm² earth conductor.

Every guide below follows that order: the circuit, the clause, the steps, the result.

Index by calculator

Arc flash

Battery

Cable size

Conduit fill

Fault rating

Full load current

Generator

IDMT protection

Loop impedance

Maximum demand

Motor

Three‑phase power

Transformer

Voltage drop

Voltage rise

The tag after each link names the trade the example was written for. The method still applies across trades: a 400 V motor feeder and a 230 V heat pump circuit take the same five checks.

To compare AmpSize with other cable size calculators, read the cable size calculators compared table.

This page is a design aid. Verify every value against the current edition of the standard.

See also: Current-carrying capacity and derating, Maximum demand and diversity and IB ≤ IN ≤ IZ: the overload rule on a 32 A circuit.

Thử với các đầu vào này

Nhiệt độ môi trường
30 °C
Lõi dây
Nhiều lõi
Đường đặc tính của thiết bị
Đường đặc tính C
Kiểm tra thiết bị bảo vệ
Có
Các mạch đi chung nhóm
1
Cách điện
PVC 75 °C
Chiều dài đoạn dây
15 m
Dòng thiết kế
20 A
Vật liệu
Đồng
Phương pháp lắp đặt
Enclosed in air
Hệ số công suất
0.9
Các pha
Một pha
Định mức thiết bị
20 A
Giới hạn sụt áp
5 %
Điện áp
230 V
Tổng trở ngoài Ze
0.35 Ω
Mở công cụ tính với các dữ liệu nhập này

Tiếp theo

Các khái niệm đứng sau nó

Thêm ví dụ tính toán

AmpSize là công cụ hỗ trợ thiết kế. Hãy đối chiếu kết quả với tiêu chuẩn hiện hành.

Thông tin này có hữu ích không?

Có câu hỏi, hoặc giá trị có vẻ sai? Liên hệ chúng tôi.