सामग्री पर जाएँ
AmpSize

This page is not in हिन्दी yet, so you are reading the English.

· 4 मिनट पढ़ने में

Loop power and the 4–20 mA voltage budget

व्यावहारिक स्तर

A drawn communications schematic for Loop power: rack, patch panel, switch, data outlet, access point and camera.

A two‑wire transmitter takes its power from the loop it signals on. It needs a minimum voltage at its terminals to work. A long cable or a heavy burden can take too much. This page shows how to check the budget.

The loop is a series circuit

The supply, the receiver, any barrier, the cable and the transmitter sit in one series loop. The same current flows through all of them. At full scale that current is 20 mA.

Each part takes some voltage. What remains is the voltage at the transmitter. The transmitter needs at least its lift-off voltage. The data sheet gives that figure.

The budget

The tool uses these steps.

  1. Find the resistance of the cable. It counts both conductors.
  2. Add the series resistance. That is the receiver input, any HART resistor and other items such as barriers.
  3. Multiply the total by the loop current to get the voltage lost.
  4. Subtract that loss from the supply to get the voltage at the transmitter.
  5. Subtract the lift-off voltage to get the margin.

A positive margin means the loop works at full scale. A negative margin means it does not.

The tool also gives the maximum loop resistance and the maximum cable length at the limit.

A worked loop

A transmitter has a lift-off voltage of 12 V. The supply is 24 V. The loop current is 20 mA. The receiver input is 250 Ω. The cable is 500 m of 1 mm² copper in New Zealand.

  • Conductor resistance: 25.8 Ω/km, from Tables 34 and 35 of AS/NZS 3008.1.2:2017
  • Cable resistance, both conductors: 25.8 Ω
  • Loop resistance: 25.8 + 250 = 275.8 Ω
  • Voltage lost: 275.8 × 0.02 = 5.516 V
  • Voltage at the transmitter: 18.48 V
  • Margin: 6.48 V

The maximum loop resistance is 12 V / 0.02 A = 600 Ω. The maximum cable length is 6782 m. This loop has a large margin.

Open the loop power tool with these inputs.

When it gets tight

Make the cable 1500 m long and add a 250 Ω HART resistor. The other inputs stay the same.

  • Loop resistance: 77.4 + 250 + 250 = 577.4 Ω
  • Voltage at the transmitter: 12.45 V
  • Margin: 0.45 V

The loop still works. The margin is small. A drop in the supply voltage would take it away. The maximum cable length falls to 1937 m.

Open the loop power tool with this loop.

Now change the conductor to 1.5 mm². The margin rises to 1.01 V. The maximum length rises to 3030 m.

Open the loop power tool with 1.5 mm².

Which supply voltage to enter

Enter the lowest voltage the supply can give. A 24 V supply can sit lower than 24 V. A margin worked at 24 V can vanish at the lower figure.

Fixes when the margin is negative

  • Use a larger conductor.
  • Use a higher supply voltage, if the loop devices allow it.
  • Remove series resistance. A smaller receiver input helps.
  • Choose a transmitter with a lower lift-off voltage.

Each fix has a cost. Check the device data sheets before you change the design.

Where it goes wrong

The cable length is counted one way. The tool takes the one-way length and counts both conductors. Do not double it.

The idle current is used. The loop draws most at full scale. Use the highest current the transmitter drives. That can be its upscale alarm current.

The supply is entered at its nominal voltage. Use the lowest voltage in service.

The HART resistor is forgotten. It adds series resistance. Enter it in its own field.

A barrier or isolator is left out. These parts add resistance too. Use the other series resistance field.

The table gives a.c. resistance at the conductor operating temperature. A d.c. loop at a lower temperature has less, so the margin is on the safe side.

This page is a design aid. Verify every value against the device maker data.

See also: 24 V DC voltage drop on an instrument loop, Choosing a comms cable: length and screen and Control panels and PLC wiring.

यह कहाँ इस्तेमाल होता है

हल किए गए उदाहरण

सभी 121 गाइड

AmpSize एक डिज़ाइन सहायक है। परिणामों को वर्तमान मानक से जाँचें।

क्या यह उपयोगी था?

कोई सवाल, या कोई मान गलत लगता है? हमसे संपर्क करें।